Glossary

Remapping and automotive electronics glossary

The terms we use every day in the laboratory, explained in one or two sentences and linked to the service where they apply. If a workshop or customer asks what a Slave is or what readiness does, this is the page.

Adaptation

Learned value a control unit must relearn after changing a part: injectors (IMA/IQA), throttle, EGR, DSG clutch, steering angle, battery.

Electronic module adaptation →
AdBlue / SCR

Selective catalytic reduction system injecting urea (AdBlue) into the exhaust to cut NOx on Euro 5 and 6 diesels. Its failure leaves the vehicle unable to start after a countdown.

AdBlue OFF →
Alientech KESS3

OBD, bench and boot remapping tool with licences by vehicle family. ASF Tech is an authorised dealer.

Alientech KESS3 and licences →
AutoTuner

Fast remapping tool with no mandatory annual subscription. ASF Tech is an authorised dealer.

AutoTuner →
Bench

Reading or writing the ECU removed and connected on the table with a harness or a bench (MAGBench). Needed on Bosch MD1/MG1 and many recent Continental units.

Guided reading and writing →
Boot mode

Direct access to the ECU microprocessor (Tricore, ST10…) to read or write when OBD and bench are not possible or the unit is bricked.

Bricked unit recovery (Back to Stock) →
Checksum

Verification sum the ECU uses to check its software is not corrupt. After editing a file it must be recalculated or the ECU will not start.

Stage 1 →
Chiptuning

Trade name for ECU remapping. From the years when the ECU chip was physically swapped; today the software is edited via OBD, bench or boot.

Stage 1 →
Clone

Copy flash and EEPROM of a faulty ECU into another of the same hardware so the car does not notice the change.

Virginising and cloning of modules →
Coding

Configuring in a control unit the vehicle variant, its pairing with other modules and its adaptations. Essential after replacing a unit.

Coding of replaced ECUs →
Damos

Definition files identifying maps (address, axes, factors) within a file of an ECU family. They speed up editing in WinOLS.

Professional software: WinOLS, technical data and deletes →
DPF / FAP

Diesel particulate filter (FAP on PSA, with additive). Traps soot and burns it in regenerations; saturates with urban use.

Particulate filter DPF / FAP OFF →
DSG

VAG group dual-clutch gearbox (DQ200, DQ250, DQ381, DQ500; S tronic DL382/DL501). Its mechatronics is remapped to accept more torque and shift faster.

DSG TCU remapping →
DTC

Diagnostic Trouble Code (P0xxx, P1xxx, U0xxx…). Describes a detected condition, not the part to change.

Fault code (DTC) interpretation →
DTC OFF

Deactivation in the ECU of specific codes resulting from a deliberate modification, keeping the rest of the diagnosis active.

DTC OFF: delete specific codes →
Dyno

Installation measuring wheel power and torque with the car stationary. Allows comparing before and after a remap with real data.

Stage 1 →
Eco tuning

Consumption-oriented remap: more torque between 1,200 and 2,500 rpm and optimised part load; 5–12% real saving on vans, trucks and fleets.

Eco: fuel saving →
ECU

Engine Control Unit. Manages injection, ignition, boost, emissions and limits. Common makers: Bosch, Continental/Siemens, Delphi, Denso, Marelli.

Engine ECU remapping →
ECU remapping

Modifying the software of the engine control unit (ECU) or gearbox (TCU) to change power, torque, consumption or the behaviour of systems such as AdBlue, DPF or EGR. Done by reading the original file, editing it and writing it back.

Stage 1 →
EEPROM

ECU memory where immobiliser, adaptations and identification data usually reside; distinct from the flash, where the calibration lives.

Immo OFF: immobiliser →
EGR

Exhaust gas recirculation into the intake to cut NOx. Builds carbon in valve, manifold and flaps.

EGR OFF →
Emulator

Module replacing the signal of an absent or faulty component (immobiliser, steering lock, seat sensor). CarLabImmo is the reference.

CarLabImmo emulators →
File service

Service where a workshop reads the ECU with its tool, sends the original file to a laboratory (ASF Tech) and receives the modified file ready to write, usually in 15–60 minutes.

Stage 1 →
FLAP / exhaust valves

Valves opening or closing the exhaust by mode and rpm. FLAP OFF controls them by software without codes.

FLAP OFF: exhaust valves →
GPF / OPF

Petrol particulate filter, mandatory on direct injection since Euro 6d-TEMP (2018).

GPF / OPF OFF →
Hardcut limiter

Hard fuel cut at the rev limiter, with the competition sound. On diesel, popcorn effect.

Hardcut Limiter and diesel Popcorn →
HVT

High-voltage safety training for working on hybrids and EVs: de-energising, PPE, verification of absence of voltage.

Hybrid and electric vehicle course (HVT) →
Immobiliser (Immo)

Anti-theft system preventing starting if the ECU does not recognise the key via the immobiliser module. Immo OFF deactivates it in cases with no alternative and proven ownership.

Immo OFF: immobiliser →
J2534 / passthru

Diagnostic interface standard allowing manufacturer or third-party software to communicate with the vehicle. Needed for online coding.

Advanced remote connection →
Launch Control

Function holding a fixed rpm with the car stopped and managing the launch with traction control. Activated in the ECU and, on automatics, the TCU.

Launch Control activation →
Log data

Real-time recording of variables (boost, temperatures, lambda, advance) while driving, used to tune a Stage 2 or 3.

Stage 2 →
Magic Motorsport FLEX

Laboratory tool for bench and boot with modules by family and the MAGBench. ASF Tech is an authorised dealer.

Magic Motorsport FLEX and MAGBench →
Map

Table inside the ECU software relating variables (rpm, load) to an output (injection quantity, boost, advance). A file has hundreds.

Engine ECU remapping →
Master

Remapping tool that reads and writes unencrypted files; allows editing in WinOLS or sending to any supplier. For tuners and laboratories.

Master or Slave guide →
OBD

On-Board Diagnostics. The vehicle's diagnostic port; many ECUs are read and written through it without removing anything.

Engine ECU remapping →
OBD readiness

State of the emissions self-test monitors (catalyst, O2, EGR, EVAP, DPF…). Must remain coherent after any modification.

Emissions monitoring (readiness) →
Online coding

Coding or adaptation performed remotely, with an engineer connected to the workshop's PC and interface (J2534).

Coding of replaced ECUs →
Original file (Back to Stock)

Copy of the ECU's factory software, read before modifying anything. Allows returning to standard at any time.

Original software (Back to Stock) →
Pop & Bang

Map keeping a small injection with retarded ignition on throttle-off so it detonates in the exhaust. Soft version: Crackle Map.

Pop & Bang →
Regeneration

Cycle in which the ECU raises exhaust temperature (post-injection) to burn soot accumulated in the DPF or GPF.

Particulate filter DPF / FAP OFF →
Slave

Tool linked to a Master: reads encrypted files only that Master opens and writes those it returns. Lower investment; the usual option for workshops.

Master or Slave guide →
Stage 1

Remap with standard hardware: +15–30% power and up to +25% torque on turbo diesel and petrol, within manufacturer margins.

Stage 1 →
Stage 2

Remap for vehicles with upgraded exhaust (downpipe), intake and intercooler; +30–45% tuned with log data.

Stage 2 →
Stage 3

Software development for new turbo, injectors and pump; requires custom tuning with log data and usually a reinforced clutch or gearbox.

Stage 3 →
Swirl flaps

Turbulence flaps in the diesel intake manifold. They seize with carbon and on some BMWs can break; removed with a kit and deleted by software.

Swirl Flaps OFF and TVA OFF →
TCU

Transmission Control Unit, the automatic or DSG gearbox controller. Decides when and how it shifts and how much torque it accepts. Remapped alongside the ECU in a Stage.

TCU: automatic gearboxes →
Torque limiter

Map setting the maximum torque the ECU requests per gear or condition. Protects clutch and gearbox; adjusted with judgement in a Stage.

Torque delivery optimisation →
Virginise

Erase the pairing of a used ECU so it can be coded to another vehicle as if new.

Virginising and cloning of modules →
VMAX

Electronic top-speed limiter (250 km/h on many German cars; 90–120 on fleets). Removed or set by software.

VMAX OFF: speed limiter →
WinOLS

EVC software to identify and edit maps in an ECU file and correct checksums. The industry standard for Masters.

Professional software: WinOLS, technical data and deletes →
ZF 8HP

ZF eight-speed torque-converter automatic fitted to BMW, Audi, JLR, Alfa Romeo and Maserati. The TCU we remap most.

TCU: automatic gearboxes →

FAQ

Frequently asked questions

What is the difference between Stage 1 and Stage 2?

Stage 1 works with standard hardware (+15–30%); Stage 2 requires upgraded exhaust, intake and intercooler (+30–45%) and is tuned with log data.

What does bench mean in remapping?

Reading or writing the ECU removed and connected on the table, needed on protected units that do not allow OBD.

What is a Slave file?

An encrypted file read with a Slave tool that only the Master it is linked to can open, in our case ASF Tech.

Contact

A term missing? Ask us

Tell us the vehicle, engine, ECU and what you want to achieve. We reply during support hours with a fixed price and lead time.

Request a quote

Data controller: ASF Motors SC (ASF Tech). Purpose: to answer your quote request. We do not share your data. You can exercise your rights as explained in the privacy policy.

Last updated: